Search

Results for: wire testing

Selection of Zones for Degradation Testing

June 26, 2020 Michael Traskos

Maintenance zones within an aircraft are not homogeneous. They vary from the extreme Aircraft areas within the aircraft (engines) to more benign areas (inside pressure and temperature-controlled areas). And because of this, the components within each of these zones will age at different rates. Naturally, different components are selected for each of these zones; those components better able to handle the severe environments are installed in those environments, and lower requirements are placed on those parts installed in benign environments. Read more

Light Weight and Normal Weight Wire Constructions

April 10, 2020 Michael Traskos

Saving weight is a large part of any aircraft design. Naturally, the electrical system is not exempt from the goal of shaving off a couple of pounds. This often comes in the form of looking for lighter connectors, lighter clamps, and also lighter wire constructions. Those that have done this have undoubtedly come across two classifications of wire construction: “Normal weight” and “light weight”. Of course, if the EWIS has to go on a diet, then the “light weight” construction looks like a good substitute for the “normal weight”… after all, why would the wire be called “light weight” if not for satisfying weight requirements. Read more

Notch Testing and the Impact of 1000 Cuts

March 4, 2020 Michael Traskos

How much damage can a single wire take? Does the failure of a wire’s insulation require one large trauma (think of dropping a hammer on it), or is it possible for the insulation to fail due to 1,000 small cuts? That has been a question plaguing wire system sustainment for decades. Identifying one large trauma can be easy, but to catalog all the minor traumas is impossible. Read more

Infographic – The Journey of An Aerospace Wire

February 21, 2020 Michael Traskos

From beginning of its life, aircraft wire and cable undergo thousands of hours of testing to ensure their reliable performance. To grasp how this process evolves, Lectromec has put together this infographic. Looking for help along the process? We can help with that too. Read more

Impact of Secondary Wire Harness Protection on Heating

December 10, 2019 Michael Traskos

If you are standing outside on a cold winter day, would you be warmer in a T-shirt or in a jacket? The answer is obvious, but somehow that ‘obvious answer’ is obscured when thinking of aircraft wire harness design. A common question of OEMs and aftermarket modifiers is: how much of an impact (if any) does secondary harness protection have on wire harness heating?

Lectromec took time this last week to put together a representative harness and run tests to generate data on the thermal impact of three secondary wire harness protection schemes. While this data is not representative of every wire harness configuration, it does provide a basis for determining if additional testing (or simulation) are needed for your application.

SAE Wire and Cable Committee Meeting Update – Fall 2019

November 3, 2019 Michael Traskos

The SAE wire and cable committee held their fall 2019 meeting in San Diego this year. As with every committee meeting, a lot of technical areas were discussed, progress was made, and some new ideas/problems are emerged. As we do after all these meetings, we put together a highlight of some of the talking points from the meeting.

Wire Diagnostic Equipment

September 17, 2019 Michael Traskos

Finding wire faults/damage is not an easy task; now consider that problem across an entire aircraft. In-situ testing of wires/cables has always been viewed as something of a challenge to the industry. Given the branching that most harnesses undergo, the various wire lengths, splices, and numerous termination conditions, it can be difficult. Attempts to automate some of the testing has come to the development of Automatic Wire Test Sets (AWTS [pronounced “Eh-Wits”]).

Because there are so many ways to test a wire harness, the US military sought to create a performance standard to cover the general ideas and best practices of this equipment. Here, we review the standard and some of the performance features that can be expected when using equipment in compliance with the standard

Wires and Fuel Compatibility

August 7, 2019 Michael Traskos

Whether by design or by accident, some wires in an aircraft will be exposed to jet fuel. Because of this, it is necessary to be prepared and select wires/cable types that will not suffer adverse effects of the exposure. Considering the impact of fuel on wiring is not idle musing about wiring systems; to quote the FAA AC120-97A, “Since 1959, there have been 18 fuel tank explosions on transport category airplanes”. Read more

Common Questions About Kapton® Wire

June 12, 2019 Michael Traskos

Love it or hate it, the fact is that Kapton® insulated wires will be on aircraft for at least another couple of decades, and because of this, we should learn to live with the insulation type. Part of living with it is understanding it. If you have questions that you would like to see answered, please send them to Lectromec or add them to the comments section below. We plan to add to this article as the questions arise. Read more

Impact of Wires Used as Ladders

May 22, 2019 Devon Gonteski

Ideally, an aircraft’s EWIS aging is considered and monitored over time, but something as simple as gripping and pulling a wire or cable can change its electrical performance, specifically conductivity and resistance. Read more